3. SPECIFICATION
3.1. Internet Header Format
A summary of the contents of the internet header follows:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|Version| IHL |Type of Service| Total Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Identification |Flags| Fragment Offset |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Time to Live | Protocol | Header Checksum |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Source Address |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Destination Address |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Options | Padding |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Example Internet Datagram Header
Figure 4.
Note that each tick mark represents one bit position.
Version: 4 bits The Version field indicates the format of the internet header. This document describes version 4. IHL: 4 bits Internet Header Length is the length of the internet header in 32 bit words, and thus points to the beginning of the data. Note that the minimum value for a correct header is 5. Type of Service: 8 bits The Type of Service provides an indication of the abstract parameters of the quality of service desired. These parameters are to be used to guide the selection of the actual service parameters when transmitting a datagram through a particular network. Several networks offer service precedence, which somehow treats high precedence traffic as more important than other traffic (generally by accepting only traffic above a certain precedence at time of high load). The major choice is a three way tradeoff between low-delay, high-reliability, and high-throughput. Bits 0-2: Precedence. Bit 3: 0 = Normal Delay, 1 = Low Delay. Bits 4: 0 = Normal Throughput, 1 = High Throughput. Bits 5: 0 = Normal Relibility, 1 = High Relibility. Bit 6-7: Reserved for Future Use. 0 1 2 3 4 5 6 7 +-----+-----+-----+-----+-----+-----+-----+-----+ | | | | | | | | PRECEDENCE | D | T | R | 0 | 0 | | | | | | | | +-----+-----+-----+-----+-----+-----+-----+-----+ Precedence 111 - Network Control 110 - Internetwork Control 101 - CRITIC/ECP 100 - Flash Override 011 - Flash 010 - Immediate 001 - Priority 000 - Routine The use of the Delay, Throughput, and Reliability indications may increase the cost (in some sense) of the service. In many networks better performance for one of these parameters is coupled with worse performance on another. Except for very unusual cases at most two of these three indications should be set. The type of service is used to specify the treatment of the datagram during its transmission through the internet system. Example mappings of the internet type of service to the actual service provided on networks such as AUTODIN II, ARPANET, SATNET, and PRNET is given in "Service Mappings" [8]. The Network Control precedence designation is intended to be used within a network only. The actual use and control of that designation is up to each network. The Internetwork Control designation is intended for use by gateway control originators only. If the actual use of these precedence designations is of concern to a particular network, it is the responsibility of that network to control the access to, and use of, those precedence designations. Total Length: 16 bits Total Length is the length of the datagram, measured in octets, including internet header and data. This field allows the length of a datagram to be up to 65,535 octets. Such long datagrams are impractical for most hosts and networks. All hosts must be prepared to accept datagrams of up to 576 octets (whether they arrive whole or in fragments). It is recommended that hosts only send datagrams larger than 576 octets if they have assurance that the destination is prepared to accept the larger datagrams. The number 576 is selected to allow a reasonable sized data block to be transmitted in addition to the required header information. For example, this size allows a data block of 512 octets plus 64 header octets to fit in a datagram. The maximal internet header is 60 octets, and a typical internet header is 20 octets, allowing a margin for headers of higher level protocols. Identification: 16 bits An identifying value assigned by the sender to aid in assembling the fragments of a datagram. Flags: 3 bits Various Control Flags. Bit 0: reserved, must be zero Bit 1: (DF) 0 = May Fragment, 1 = Don't Fragment. Bit 2: (MF) 0 = Last Fragment, 1 = More Fragments. 0 1 2 +---+---+---+ | | D | M | | 0 | F | F | +---+---+---+ Fragment Offset: 13 bits This field indicates where in the datagram this fragment belongs. The fragment offset is measured in units of 8 octets (64 bits). The first fragment has offset zero. Time to Live: 8 bits This field indicates the maximum time the datagram is allowed to remain in the internet system. If this field contains the value zero, then the datagram must be destroyed. This field is modified in internet header processing. The time is measured in units of seconds, but since every module that processes a datagram must decrease the TTL by at least one even if it process the datagram in less than a second, the TTL must be thought of only as an upper bound on the time a datagram may exist. The intention is to cause undeliverable datagrams to be discarded, and to bound the maximum datagram lifetime. Protocol: 8 bits This field indicates the next level protocol used in the data portion of the internet datagram. The values for various protocols are specified in "Assigned Numbers" [9]. Header Checksum: 16 bits A checksum on the header only. Since some header fields change (e.g., time to live), this is recomputed and verified at each point that the internet header is processed. The checksum algorithm is: The checksum field is the 16 bit one's complement of the one's complement sum of all 16 bit words in the header. For purposes of computing the checksum, the value of the checksum field is zero. This is a simple to compute checksum and experimental evidence indicates it is adequate, but it is provisional and may be replaced by a CRC procedure, depending on further experience. Source Address: 32 bits The source address. See section 3.2. Destination Address: 32 bits The destination address. See section 3.2. Options: variable The options may appear or not in datagrams. They must be implemented by all IP modules (host and gateways). What is optional is their transmission in any particular datagram, not their implementation. In some environments the security option may be required in all datagrams. The option field is variable in length. There may be zero or more options. There are two cases for the format of an option: Case 1: A single octet of option-type. Case 2: An option-type octet, an option-length octet, and the actual option-data octets. The option-length octet counts the option-type octet and the option-length octet as well as the option-data octets. The option-type octet is viewed as having 3 fields: 1 bit copied flag, 2 bits option class, 5 bits option number. The copied flag indicates that this option is copied into all fragments on fragmentation. 0 = not copied 1 = copied The option classes are: 0 = control 1 = reserved for future use 2 = debugging and measurement 3 = reserved for future use The following internet options are defined: CLASS NUMBER LENGTH DESCRIPTION ----- ------ ------ ----------- 0 0 - End of Option list. This option occupies only 1 octet; it has no length octet. 0 1 - No Operation. This option occupies only 1 octet; it has no length octet. 0 2 11 Security. Used to carry Security, Compartmentation, User Group (TCC), and Handling Restriction Codes compatible with DOD requirements. 0 3 var. Loose Source Routing. Used to route the internet datagram based on information supplied by the source. 0 9 var. Strict Source Routing. Used to route the internet datagram based on information supplied by the source. 0 7 var. Record Route. Used to trace the route an internet datagram takes. 0 8 4 Stream ID. Used to carry the stream identifier. 2 4 var. Internet Timestamp. Specific Option Definitions End of Option List +--------+ |00000000| +--------+ Type=0 This option indicates the end of the option list. This might not coincide with the end of the internet header according to the internet header length. This is used at the end of all options, not the end of each option, and need only be used if the end of the options would not otherwise coincide with the end of the internet header. May be copied, introduced, or deleted on fragmentation, or for any other reason. No Operation +--------+ |00000001| +--------+ Type=1 This option may be used between options, for example, to align the beginning of a subsequent option on a 32 bit boundary. May be copied, introduced, or deleted on fragmentation, or for any other reason. Security This option provides a way for hosts to send security, compartmentation, handling restrictions, and TCC (closed user group) parameters. The format for this option is as follows: +--------+--------+---//---+---//---+---//---+---//---+ |10000010|00001011|SSS SSS|CCC CCC|HHH HHH| TCC | +--------+--------+---//---+---//---+---//---+---//---+ Type=130 Length=11 Security (S field): 16 bits Specifies one of 16 levels of security (eight of which are reserved for future use). 00000000 00000000 - Unclassified 11110001 00110101 - Confidential 01111000 10011010 - EFTO 10111100 01001101 - MMMM 01011110 00100110 - PROG 10101111 00010011 - Restricted 11010111 10001000 - Secret 01101011 11000101 - Top Secret 00110101 11100010 - (Reserved for future use) 10011010 11110001 - (Reserved for future use) 01001101 01111000 - (Reserved for future use) 00100100 10111101 - (Reserved for future use) 00010011 01011110 - (Reserved for future use) 10001001 10101111 - (Reserved for future use) 11000100 11010110 - (Reserved for future use) 11100010 01101011 - (Reserved for future use) Compartments (C field): 16 bits An all zero value is used when the information transmitted is not compartmented. Other values for the compartments field may be obtained from the Defense Intelligence Agency. Handling Restrictions (H field): 16 bits The values for the control and release markings are alphanumeric digraphs and are defined in the Defense Intelligence Agency Manual DIAM 65-19, "Standard Security Markings". Transmission Control Code (TCC field): 24 bits Provides a means to segregate traffic and define controlled communities of interest among subscribers. The TCC values are trigraphs, and are available from HQ DCA Code 530. Must be copied on fragmentation. This option appears at most once in a datagram. Loose Source and Record Route +--------+--------+--------+---------//--------+ |10000011| length | pointer| route data | +--------+--------+--------+---------//--------+ Type=131 The loose source and record route (LSRR) option provides a means for the source of an internet datagram to supply routing information to be used by the gateways in forwarding the datagram to the destination, and to record the route information. The option begins with the option type code. The second octet is the option length which includes the option type code and the length octet, the pointer octet, and length-3 octets of route data. The third octet is the pointer into the route data indicating the octet which begins the next source address to be processed. The pointer is relative to this option, and the smallest legal value for the pointer is 4. A route data is composed of a series of internet addresses. Each internet address is 32 bits or 4 octets. If the pointer is greater than the length, the source route is empty (and the recorded route full) and the routing is to be based on the destination address field. If the address in destination address field has been reached and the pointer is not greater than the length, the next address in the source route replaces the address in the destination address field, and the recorded route address replaces the source address just used, and pointer is increased by four. The recorded route address is the internet module's own internet address as known in the environment into which this datagram is being forwarded. This procedure of replacing the source route with the recorded route (though it is in the reverse of the order it must be in to be used as a source route) means the option (and the IP header as a whole) remains a constant length as the datagram progresses through the internet. This option is a loose source route because the gateway or host IP is allowed to use any route of any number of other intermediate gateways to reach the next address in the route. Must be copied on fragmentation. Appears at most once in a datagram. Strict Source and Record Route +--------+--------+--------+---------//--------+ |10001001| length | pointer| route data | +--------+--------+--------+---------//--------+ Type=137 The strict source and record route (SSRR) option provides a means for the source of an internet datagram to supply routing information to be used by the gateways in forwarding the datagram to the destination, and to record the route information. The option begins with the option type code. The second octet is the option length which includes the option type code and the length octet, the pointer octet, and length-3 octets of route data. The third octet is the pointer into the route data indicating the octet which begins the next source address to be processed. The pointer is relative to this option, and the smallest legal value for the pointer is 4. A route data is composed of a series of internet addresses. Each internet address is 32 bits or 4 octets. If the pointer is greater than the length, the source route is empty (and the recorded route full) and the routing is to be based on the destination address field. If the address in destination address field has been reached and the pointer is not greater than the length, the next address in the source route replaces the address in the destination address field, and the recorded route address replaces the source address just used, and pointer is increased by four. The recorded route address is the internet module's own internet address as known in the environment into which this datagram is being forwarded. This procedure of replacing the source route with the recorded route (though it is in the reverse of the order it must be in to be used as a source route) means the option (and the IP header as a whole) remains a constant length as the datagram progresses through the internet. This option is a strict source route because the gateway or host IP must send the datagram directly to the next address in the source route through only the directly connected network indicated in the next address to reach the next gateway or host specified in the route. Must be copied on fragmentation. Appears at most once in a datagram. Record Route +--------+--------+--------+---------//--------+ |00000111| length | pointer| route data | +--------+--------+--------+---------//--------+ Type=7 The record route option provides a means to record the route of an internet datagram. The option begins with the option type code. The second octet is the option length which includes the option type code and the length octet, the pointer octet, and length-3 octets of route data. The third octet is the pointer into the route data indicating the octet which begins the next area to store a route address. The pointer is relative to this option, and the smallest legal value for the pointer is 4. A recorded route is composed of a series of internet addresses. Each internet address is 32 bits or 4 octets. If the pointer is greater than the length, the recorded route data area is full. The originating host must compose this option with a large enough route data area to hold all the address expected. The size of the option does not change due to adding addresses. The intitial contents of the route data area must be zero. When an internet module routes a datagram it checks to see if the record route option is present. If it is, it inserts its own internet address as known in the environment into which this datagram is being forwarded into the recorded route begining at the octet indicated by the pointer, and increments the pointer by four. If the route data area is already full (the pointer exceeds the length) the datagram is forwarded without inserting the address into the recorded route. If there is some room but not enough room for a full address to be inserted, the original datagram is considered to be in error and is discarded. In either case an ICMP parameter problem message may be sent to the source host [3]. Not copied on fragmentation, goes in first fragment only. Appears at most once in a datagram. Stream Identifier +--------+--------+--------+--------+ |10001000|00000010| Stream ID | +--------+--------+--------+--------+ Type=136 Length=4 This option provides a way for the 16-bit SATNET stream identifier to be carried through networks that do not support the stream concept. Must be copied on fragmentation. Appears at most once in a datagram. Internet Timestamp +--------+--------+--------+--------+ |01000100| length | pointer|oflw|flg| +--------+--------+--------+--------+ | internet address | +--------+--------+--------+--------+ | timestamp | +--------+--------+--------+--------+ | . | . . Type = 68 The Option Length is the number of octets in the option counting the type, length, pointer, and overflow/flag octets (maximum length 40). The Pointer is the number of octets from the beginning of this option to the end of timestamps plus one (i.e., it points to the octet beginning the space for next timestamp). The smallest legal value is 5. The timestamp area is full when the pointer is greater than the length. The Overflow (oflw) [4 bits] is the number of IP modules that cannot register timestamps due to lack of space. The Flag (flg) [4 bits] values are 0 -- time stamps only, stored in consecutive 32-bit words, 1 -- each timestamp is preceded with internet address of the registering entity, 3 -- the internet address fields are prespecified. An IP module only registers its timestamp if it matches its own address with the next specified internet address. The Timestamp is a right-justified, 32-bit timestamp in milliseconds since midnight UT. If the time is not available in milliseconds or cannot be provided with respect to midnight UT then any time may be inserted as a timestamp provided the high order bit of the timestamp field is set to one to indicate the use of a non-standard value. The originating host must compose this option with a large enough timestamp data area to hold all the timestamp information expected. The size of the option does not change due to adding timestamps. The intitial contents of the timestamp data area must be zero or internet address/zero pairs. If the timestamp data area is already full (the pointer exceeds the length) the datagram is forwarded without inserting the timestamp, but the overflow count is incremented by one. If there is some room but not enough room for a full timestamp to be inserted, or the overflow count itself overflows, the original datagram is considered to be in error and is discarded. In either case an ICMP parameter problem message may be sent to the source host [3]. The timestamp option is not copied upon fragmentation. It is carried in the first fragment. Appears at most once in a datagram. Padding: variable The internet header padding is used to ensure that the internet header ends on a 32 bit boundary. The padding is zero.
3.2. Discussion
The implementation of a protocol must be robust. Each implementation must expect to interoperate with others created by different individuals. While the goal of this specification is to be explicit about the protocol there is the possibility of differing interpretations. In general, an implementation must be conservative in its sending behavior, and liberal in its receiving behavior. That is, it must be careful to send well-formed datagrams, but must accept any datagram that it can interpret (e.g., not object to technical errors where the meaning is still clear).
The basic internet service is datagram oriented and provides for the fragmentation of datagrams at gateways, with reassembly taking place at the destination internet protocol module in the destination host. Of course, fragmentation and reassembly of datagrams within a network or by private agreement between the gateways of a network is also allowed since this is transparent to the internet protocols and the higher-level protocols. This transparent type of fragmentation and reassembly is termed "network-dependent" (or intranet) fragmentation and is not discussed further here.
Internet addresses distinguish sources and destinations to the host level and provide a protocol field as well. It is assumed that each protocol will provide for whatever multiplexing is necessary within a host.
To provide for flexibility in assigning address to networks and allow for the large number of small to intermediate sized networks the interpretation of the address field is coded to specify a small number of networks with a large number of host, a moderate number of networks with a moderate number of hosts, and a large number of networks with a small number of hosts. In addition there is an escape code for extended addressing mode.
High Order Bits Format Class
--------------- ------------------------------- -----
0 7 bits of net, 24 bits of host a
10 14 bits of net, 16 bits of host b
110 21 bits of net, 8 bits of host c
111 escape to extended addressing mode
A value of zero in the network field means this network. This is only used in certain ICMP messages. The extended addressing mode is undefined. Both of these features are reserved for future use.
The actual values assigned for network addresses is given in "Assigned Numbers" [9].
The local address, assigned by the local network, must allow for a single physical host to act as several distinct internet hosts. That is, there must be a mapping between internet host addresses and network/host interfaces that allows several internet addresses to correspond to one interface. It must also be allowed for a host to have several physical interfaces and to treat the datagrams from several of them as if they were all addressed to a single host.
Address mappings between internet addresses and addresses for ARPANET, SATNET, PRNET, and other networks are described in "Address Mappings" [5].
Fragmentation and Reassembly.
The internet identification field (ID) is used together with the source and destination address, and the protocol fields, to identify datagram fragments for reassembly.
The More Fragments flag bit (MF) is set if the datagram is not the last fragment. The Fragment Offset field identifies the fragment location, relative to the beginning of the original unfragmented datagram. Fragments are counted in units of 8 octets. The fragmentation strategy is designed so than an unfragmented datagram has all zero fragmentation information (MF = 0, fragment offset = 0). If an internet datagram is fragmented, its data portion must be broken on 8 octet boundaries.
This format allows 2**13 = 8192 fragments of 8 octets each for a total of 65,536 octets. Note that this is consistent with the the datagram total length field (of course, the header is counted in the total length and not in the fragments).
When fragmentation occurs, some options are copied, but others remain with the first fragment only.
Every internet module must be able to forward a datagram of 68 octets without further fragmentation. This is because an internet header may be up to 60 octets, and the minimum fragment is 8 octets.
Every internet destination must be able to receive a datagram of 576 octets either in one piece or in fragments to be reassembled.
The fields which may be affected by fragmentation include:
(1) options field
(2) more fragments flag
(3) fragment offset
(4) internet header length field
(5) total length field
(6) header checksum
If the Don't Fragment flag (DF) bit is set, then internet fragmentation of this datagram is NOT permitted, although it may be discarded. This can be used to prohibit fragmentation in cases where the receiving host does not have sufficient resources to reassemble internet fragments.
One example of use of the Don't Fragment feature is to down line load a small host. A small host could have a boot strap program that accepts a datagram stores it in memory and then executes it.
The fragmentation and reassembly procedures are most easily described by examples. The following procedures are example implementations.
General notation in the following pseudo programs: "=<" means "less than or equal", "#" means "not equal", "=" means "equal", "<-" means "is set to". Also, "x to y" includes x and excludes y; for example, "4 to 7" would include 4, 5, and 6 (but not 7).
An Example Fragmentation Procedure
The maximum sized datagram that can be transmitted through the next network is called the maximum transmission unit (MTU).
If the total length is less than or equal the maximum transmission unit then submit this datagram to the next step in datagram processing; otherwise cut the datagram into two fragments, the first fragment being the maximum size, and the second fragment being the rest of the datagram. The first fragment is submitted to the next step in datagram processing, while the second fragment is submitted to this procedure in case it is still too large.
Notation:
FO - Fragment Offset
IHL - Internet Header Length
DF - Don't Fragment flag
MF - More Fragments flag
TL - Total Length
OFO - Old Fragment Offset
OIHL - Old Internet Header Length
OMF - Old More Fragments flag
OTL - Old Total Length
NFB - Number of Fragment Blocks
MTU - Maximum Transmission Unit
Procedure:
IF TL =< MTU THEN Submit this datagram to the next step
in datagram processing ELSE IF DF = 1 THEN discard the
datagram ELSE
To produce the first fragment:
(1) Copy the original internet header;
(2) OIHL <- IHL; OTL <- TL; OFO <- FO; OMF <- MF;
(3) NFB <- (MTU-IHL*4)/8;
(4) Attach the first NFB*8 data octets;
(5) Correct the header:
MF <- 1; TL <- (IHL*4)+(NFB*8);
Recompute Checksum;
(6) Submit this fragment to the next step in
datagram processing;
To produce the second fragment:
(7) Selectively copy the internet header (some options
are not copied, see option definitions);
(8) Append the remaining data;
(9) Correct the header:
IHL <- (((OIHL*4)-(length of options not copied))+3)/4;
TL <- OTL - NFB*8 - (OIHL-IHL)*4);
FO <- OFO + NFB; MF <- OMF; Recompute Checksum;
(10) Submit this fragment to the fragmentation test; DONE.
In the above procedure each fragment (except the last) was made the maximum allowable size. An alternative might produce less than the maximum size datagrams. For example, one could implement a fragmentation procedure that repeatly divided large datagrams in half until the resulting fragments were less than the maximum transmission unit size.
An Example Reassembly Procedure
For each datagram the buffer identifier is computed as the concatenation of the source, destination, protocol, and identification fields. If this is a whole datagram (that is both the fragment offset and the more fragments fields are zero), then any reassembly resources associated with this buffer identifier are released and the datagram is forwarded to the next step in datagram processing.
If no other fragment with this buffer identifier is on hand then reassembly resources are allocated. The reassembly resources consist of a data buffer, a header buffer, a fragment block bit table, a total data length field, and a timer. The data from the fragment is placed in the data buffer according to its fragment offset and length, and bits are set in the fragment block bit table corresponding to the fragment blocks received.
If this is the first fragment (that is the fragment offset is zero) this header is placed in the header buffer. If this is the last fragment ( that is the more fragments field is zero) the total data length is computed. If this fragment completes the datagram (tested by checking the bits set in the fragment block table), then the datagram is sent to the next step in datagram processing; otherwise the timer is set to the maximum of the current timer value and the value of the time to live field from this fragment; and the reassembly routine gives up control.
If the timer runs out, the all reassembly resources for this buffer identifier are released. The initial setting of the timer is a lower bound on the reassembly waiting time. This is because the waiting time will be increased if the Time to Live in the arriving fragment is greater than the current timer value but will not be decreased if it is less. The maximum this timer value could reach is the maximum time to live (approximately 4.25 minutes). The current recommendation for the initial timer setting is 15 seconds. This may be changed as experience with this protocol accumulates. Note that the choice of this parameter value is related to the buffer capacity available and the data rate of the transmission medium; that is, data rate times timer value equals buffer size (e.g., 10Kb/s X 15s = 150Kb).
Notation:
FO - Fragment Offset
IHL - Internet Header Length
MF - More Fragments flag
TTL - Time To Live
NFB - Number of Fragment Blocks
TL - Total Length
TDL - Total Data Length
BUFID - Buffer Identifier
RCVBT - Fragment Received Bit Table
TLB - Timer Lower Bound
Procedure:
(1) BUFID <- source|destination|protocol|identification;
(2) IF FO = 0 AND MF = 0
(3) THEN IF buffer with BUFID is allocated
(4) THEN flush all reassembly for this BUFID;
(5) Submit datagram to next step; DONE.
(6) ELSE IF no buffer with BUFID is allocated
(7) THEN allocate reassembly resources
with BUFID;
TIMER <- TLB; TDL <- 0;
(8) put data from fragment into data buffer with
BUFID from octet FO*8 to
octet (TL-(IHL*4))+FO*8;
(9) set RCVBT bits from FO
to FO+((TL-(IHL*4)+7)/8);
(10) IF MF = 0 THEN TDL <- TL-(IHL*4)+(FO*8)
(11) IF FO = 0 THEN put header in header buffer
(12) IF TDL # 0
(13) AND all RCVBT bits from 0
to (TDL+7)/8 are set
(14) THEN TL <- TDL+(IHL*4)
(15) Submit datagram to next step;
(16) free all reassembly resources
for this BUFID; DONE.
(17) TIMER <- MAX(TIMER,TTL);
(18) give up until next fragment or timer expires;
(19) timer expires: flush all reassembly with this BUFID; DONE.
In the case that two or more fragments contain the same data either identically or through a partial overlap, this procedure will use the more recently arrived copy in the data buffer and datagram delivered.
Identification
The choice of the Identifier for a datagram is based on the need to provide a way to uniquely identify the fragments of a particular datagram. The protocol module assembling fragments judges fragments to belong to the same datagram if they have the same source, destination, protocol, and Identifier. Thus, the sender must choose the Identifier to be unique for this source, destination pair and protocol for the time the datagram (or any fragment of it) could be alive in the internet.
It seems then that a sending protocol module needs to keep a table of Identifiers, one entry for each destination it has communicated with in the last maximum packet lifetime for the internet.
However, since the Identifier field allows 65,536 different values, some host may be able to simply use unique identifiers independent of destination.
It is appropriate for some higher level protocols to choose the identifier. For example, TCP protocol modules may retransmit an identical TCP segment, and the probability for correct reception would be enhanced if the retransmission carried the same identifier as the original transmission since fragments of either datagram could be used to construct a correct TCP segment.
The type of service (TOS) is for internet service quality selection. The type of service is specified along the abstract parameters precedence, delay, throughput, and reliability. These abstract parameters are to be mapped into the actual service parameters of the particular networks the datagram traverses.
Precedence. An independent measure of the importance of this datagram.
Delay. Prompt delivery is important for datagrams with this indication.
Throughput. High data rate is important for datagrams with this indication.
Reliability. A higher level of effort to ensure delivery is important for datagrams with this indication.
For example, the ARPANET has a priority bit, and a choice between "standard" messages (type 0) and "uncontrolled" messages (type 3), (the choice between single packet and multipacket messages can also be considered a service parameter). The uncontrolled messages tend to be less reliably delivered and suffer less delay. Suppose an internet datagram is to be sent through the ARPANET. Let the internet type of service be given as:
Precedence: 5
Delay: 0
Throughput: 1
Reliability: 1
In this example, the mapping of these parameters to those available for the ARPANET would be to set the ARPANET priority bit on since the Internet precedence is in the upper half of its range, to select standard messages since the throughput and reliability requirements are indicated and delay is not. More details are given on service mappings in "Service Mappings" [8].
The time to live is set by the sender to the maximum time the datagram is allowed to be in the internet system. If the datagram is in the internet system longer than the time to live, then the datagram must be destroyed.
This field must be decreased at each point that the internet header is processed to reflect the time spent processing the datagram. Even if no local information is available on the time actually spent, the field must be decremented by 1. The time is measured in units of seconds (i.e. the value 1 means one second). Thus, the maximum time to live is 255 seconds or 4.25 minutes. Since every module that processes a datagram must decrease the TTL by at least one even if it process the datagram in less than a second, the TTL must be thought of only as an upper bound on the time a datagram may exist. The intention is to cause undeliverable datagrams to be discarded, and to bound the maximum datagram lifetime.
Some higher level reliable connection protocols are based on assumptions that old duplicate datagrams will not arrive after a certain time elapses. The TTL is a way for such protocols to have an assurance that their assumption is met.
Options
The options are optional in each datagram, but required in implementations. That is, the presence or absence of an option is the choice of the sender, but each internet module must be able to parse every option. There can be several options present in the option field.
The options might not end on a 32-bit boundary. The internet header must be filled out with octets of zeros. The first of these would be interpreted as the end-of-options option, and the remainder as internet header padding.
Every internet module must be able to act on every option. The Security Option is required if classified, restricted, or compartmented traffic is to be passed.
The internet header checksum is recomputed if the internet header is changed. For example, a reduction of the time to live, additions or changes to internet options, or due to fragmentation. This checksum at the internet level is intended to protect the internet header fields from transmission errors.
There are some applications where a few data bit errors are acceptable while retransmission delays are not. If the internet protocol enforced data correctness such applications could not be supported.
Errors
Internet protocol errors may be reported via the ICMP messages [3].
3.3. Interfaces
The functional description of user interfaces to the IP is, at best, fictional, since every operating system will have different facilities. Consequently, we must warn readers that different IP implementations may have different user interfaces. However, all IPs must provide a certain minimum set of services to guarantee that all IP implementations can support the same protocol hierarchy. This section specifies the functional interfaces required of all IP implementations.
Internet protocol interfaces on one side to the local network and on the other side to either a higher level protocol or an application program. In the following, the higher level protocol or application program (or even a gateway program) will be called the "user" since it is using the internet module. Since internet protocol is a datagram protocol, there is minimal memory or state maintained between datagram transmissions, and each call on the internet protocol module by the user supplies all information necessary for the IP to perform the service requested.
An Example Upper Level Interface
The following two example calls satisfy the requirements for the user to internet protocol module communication ("=>" means returns):
SEND (src, dst, prot, TOS, TTL, BufPTR, len, Id, DF, opt => result) where: src = source address dst = destination address prot = protocol TOS = type of service TTL = time to live BufPTR = buffer pointer len = length of buffer Id = Identifier DF = Don't Fragment opt = option data result = response OK = datagram sent ok Error = error in arguments or local network error Note that the precedence is included in the TOS and the security/compartment is passed as an option. RECV (BufPTR, prot, => result, src, dst, TOS, len, opt) where: BufPTR = buffer pointer prot = protocol result = response OK = datagram received ok Error = error in arguments len = length of buffer src = source address dst = destination address TOS = type of service opt = option data
When the user sends a datagram, it executes the SEND call supplying all the arguments. The internet protocol module, on receiving this call, checks the arguments and prepares and sends the message. If the arguments are good and the datagram is accepted by the local network, the call returns successfully. If either the arguments are bad, or the datagram is not accepted by the local network, the call returns unsuccessfully. On unsuccessful returns, a reasonable report must be made as to the cause of the problem, but the details of such reports are up to individual implementations.
When a datagram arrives at the internet protocol module from the local network, either there is a pending RECV call from the user addressed or there is not. In the first case, the pending call is satisfied by passing the information from the datagram to the user. In the second case, the user addressed is notified of a pending datagram. If the user addressed does not exist, an ICMP error message is returned to the sender, and the data is discarded.
The notification of a user may be via a pseudo interrupt or similar mechanism, as appropriate in the particular operating system environment of the implementation.
A user's RECV call may then either be immediately satisfied by a pending datagram, or the call may be pending until a datagram arrives.
The source address is included in the send call in case the sending host has several addresses (multiple physical connections or logical addresses). The internet module must check to see that the source address is one of the legal address for this host.
An implementation may also allow or require a call to the internet module to indicate interest in or reserve exclusive use of a class of datagrams (e.g., all those with a certain value in the protocol field).
This section functionally characterizes a USER/IP interface. The notation used is similar to most procedure of function calls in high level languages, but this usage is not meant to rule out trap type service calls (e.g., SVCs, UUOs, EMTs), or any other form of interprocess communication.